TODAY'S DEALS

Sharp ANALOG Copier Simulation and Test Codes
For analog copiers 1980-1995
Press & hold "0" key for total count.

For information only
Some tests may damage copier, USE AT YOUR OWN RISK!
NOT for use with Sharp Digital Copiers


Press "Clear", "Interrupt", "0", "Interrupt".
OR
"Clear, "0", "0", "Clear".
OR
"Clear", "Repeat", "0", "Pause".

Then enter Simulation # and press "Print" key to enter selected simulation.
1: Drives scan/checks scan switches
2: Manually move scanner and check switches
3: Check paper path switches and in some machines cassette switches
4: Cassette switches
5: Lights up all display on panel
6. Heat lamp on/off 5 times
7: Light exposure lamp
8: Turns on bias voltage continuously
9: Turns on charge corona
10: Turns on transfer corona
11: Turns on discharge corona continuously
12: Turns on blank discharge lamp
13: Resets U1
14: Resets H3, H4, ect.
16: Check maintenance preset #
18: Check total count
19: Check copies since last PM
20: Reset PM counter to 0
21: Aging and check warmup
22: Aging without paper
23: Aging no worm up or misfeed
24: Instant ready
25: Developer stir/calibration
26: Check lens motion (1 cycle)
27: Check lens motion
30: Test ADF switches
31: Test ADF
33: Check ADF/RADF components.
    0: Forward feed motor.
    1: Reverse feed motor.
    2: Forward transport motor.
    3: Reverse transport motor.
    4: Exit motor speed normal.
    5: Exit motor speed slow.
    6: Paper feed solenoid.
    7: Reverse solenoid.
    8: Stopper solenoid.
34: Test drum separator.
39: Adjust document sensing.
40: Reads developer preset
41: Reads copy # since developer change
42: Resets copies on developer
45: Drum setting. First value read is current to machine setting. Enter new # to match the highest # on front flange of drum.
46: Adjust exposure. Use # key to change settings.
47: AE setting. Scan half way. Read display. Press {Print} to change exposure lamp voltage settings in 5 volt increments.
48: Horizontal magnification.
49: Vertical magnification.
50: Lead edge registrations. Use# key to change setting.
54: Transport roller rimming. Use {Print} switch to change setting
57: Edge erase setting. Change with # keys.
58: Lead edge and void adjustments Use zoom keys.
60: Original detection adjustment. See service manual
63: Test duplicate sensors. Actuate sensor and watch display.
64: Sorter componets.
    0: Solenoid
    1: Motor
    2: Gate
68: Test duplex componets.
    0: Transport
    1: Paper feed
    2: Duplex / Overlay gate
    3: Paper Stop Feed
    4: Registration clutch
    5: Alignment plate
    6: Trail edge stopper
    7: Duplex reverse solenoid
70: ADF total count.
71: Duplex total count.
75: Reset ADF count to 0.
76: Reset Duplex count to 0.
77: Lens rank.
78. Setting up auto clear and double cout for 11x17. CPOP 78 "Print". When "ready" lights, enter #, press "Print" to lock in ("Ready" will go off).
    0: No auto clear; Double count on PM and total.
    1: No auto clear; Double count on PM, single on total.
    2: No auto clear; Signle count on PM, double on total.
    3: No auto clear; Single count on PM and total.
    40: Auto clear; Double count on PM and total.
    41: Auto clear; Double count on PM, single on total.
    42: Auto clear; single count on PM, double count on total.
    43: Auto clear; Single count on PM and total.
79: Country setting.
                 8500     8800
    Japan           14        4
    Metric          15        5
    Sharp Only      12        2
    Inch (U.S.)     17        7

80: Setting options.
    1: ADF only.
    2: RADF only.
    10: Duplex only.
    11: ADF and Duplex.
    12: RADF and Duplex.
    20: 15 bin sorter only.
    21: 15 bin sorter and ADF.
    22: 15 bin sorter and RADF.
    30: 15 bin sorter and duplex.
    31: 15 bin sorter, ADF, duplex.
    32: 15 bin sorter, RADF, duplex.
    40: 20 bin sorter only.
    41: 20 bin sorter and ADF.
    42: 20 bin sorter and RADF.
    50: 20 bin sorter and duplex.
    51: 20 bin sorter, ADF, duplex.
    52: 20 bin sorter, RADF, duplex,
94: Check and adjust orginial sensor.
95: 8500 Language display. English: RPM #1, set to "0".
97: send toner to transport.


 © 1996- OlsonBros. All rights reserved
 Copyright | Privacy Statement | Contact Us